Differences

This shows you the differences between two versions of the page.

--- sovol_mods [2024/03/14 15:23] – torte
+++ sovol_mods [2025/01/21 12:21] (current) – torte
@@ Line 1: / Line 1: @@
-===== Sovol KlipperScreen =====
+{{page>redirect#this_wiki_has_moved}}
+https://torte71.github.io/InsideSovolKlipperScreen/sovol_mods.html
+{{page>redirect#section}}
+----
+===== Sovol KlipperScreen (Makerbase MKS KLIPAD50) =====
 Please note that this is just work-in-progress.\\
-The changes listed here are not complete and the services below will probably need more work to function.\\
+The changes listed here may not be complete and are just quickly tested.\\
 Thanks to Vasyl Gontar for his additions/corrections to this list.
@@ Line 114: / Line 119: @@
   * **Installs system updates**
   * Files: [[makerbase-auto-fresh-files]]
+  * Unofficial package: {{ :wiki:makerbase-auto-fresh-service.deb |}}
   * Details:
     * if existing: install ''/root/system_deb/*.deb'' and reboot
@@ Line 125: / Line 131: @@
   * **Mounts all storage devices/partitions under /home/mks/printer_data/gcodes/USB/**
   * Files: [[makerbase-automount-files]]
+  * Unofficial package: {{ :wiki:makerbase-automount-service.deb |}}
   * Useful for those who want to have USB-drives automatically mounted as gcode storage
 === makerbase-beep.service ===
   * **Beeps if touchscreen is touched**
   * Files: [[makerbase-beep-files]]
+  * Unofficial package: {{ :wiki:makerbase-beep-service.deb |}}
   * Details:
     * initializes GPIO#82 (beeper pin)
@@ Line 137: / Line 145: @@
   * **Updates ''serial:'' from section ''[mcu]'' in ''home/mks/printer_data/config/printer.cfg''**
   * Files: [[makerbase-byid-files]]
+  * Unofficial package: {{ :wiki:makerbase-byid-service.deb |}}
   * Probably useless, the name of the serial connection doesn't change
 === makerbase-net-mods.service ===
   * **copies ''/boot/wpa_supplicant-wlan0.conf'' (if existing) into ''/etc/wpa_supplicant/''**
   * Files: [[makerbase-net-mods-files]]
+  * Unofficial package: {{ :wiki:makerbase-net-mods-service.deb |}}
   * Probably useless, you can configure wifi on the screen
 === makerbase-soft-shutdown.service ===
@@ Line 146: / Line 156: @@
   * does something with the "supper" capacitor
   * Files: [[makerbase-soft-shutdown-files]]
+  * Unofficial package: {{ :wiki:makerbase-soft-shutdown-service.deb |}}
   * Useless
 === makerbase-timezone-monitor.service ===
@@ Line 151: / Line 162: @@
   * Update timezone to that from ''/home/mks/target_timezone.txt''
   * Files: [[makerbase-timezone-monitor-files]]
+  * Unofficial package: {{ :wiki:makerbase-timezone-monitor-service.deb |}}
   * requires ''/home/mks/target_timezone.txt''
   * Probably useless, works fine without
 === makerbase-wlan0.service ===
-  * **configures wifi**
+  * **configures wpa_supplicant**
   * Files: [[makerbase-wlan0-files]]
+  * Unofficial package: {{ :wiki:makerbase-wlan0-service.deb |}}
   * Probably useless, works fine without
 ----
-==== Reverting ====
 === power loss recovery (plr) ===
+  * **resumes print after power failure**
+  * origin: https://github.com/The--Captain/plr-klipper
   * Used files:
     * {{ wiki:plr.cfg|~/printer_data/config/plr.cfg }}
     * {{ wiki:plr.sh|~/plr.sh }}
     * {{ wiki:clear_plr.sh|~/clear_plr.sh }}
+  * Unofficial package: {{ :wiki:plr-klipper.deb |}}
+  * Included in Sovol's default printer.cfg, thus it's recommended
+----
+==== Reverting ====
+=== power loss recovery (plr) ===
-++++remove power loss recovery |
     - Make a backup of printer.cfg!
     - Edit printer.cfg, find and remove the 3 paragraphs shown below.
@@ Line 203: / Line 221: @@
 </code>
-++++
+----
+Back to [[start]]