rebuilding
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| rebuilding [2024/08/27 10:55] – [Rebuilding] torte | rebuilding [2025/01/21 12:27] (current) – torte | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== Sovol KlipperScreen ===== | + | {{page> |
| - | ==== Rebuilding ==== | + | https:// |
| + | {{page> | ||
| + | ---- | ||
| + | |||
| + | ====== Sovol KlipperScreen | ||
| + | ===== Rebuilding | ||
| Sovol' | Sovol' | ||
| Line 13: | Line 18: | ||
| Steps to set up: | Steps to set up: | ||
| - | === Base system === | + | ==== Base system |
| - Select and download an image from https:// | - Select and download an image from https:// | ||
| Line 34: | Line 39: | ||
| * otherwise, choose the setting according to your location/ | * otherwise, choose the setting according to your location/ | ||
| - | === Klipper === | + | ==== Klipper |
| - Log into device using ssh, putty or serial connection | - Log into device using ssh, putty or serial connection | ||
| - cd into home dir: < | - cd into home dir: < | ||
| Line 107: | Line 112: | ||
| (unless you've installed the wifi-enabled dtb below - in that case, it will be spidev0.0 again). | (unless you've installed the wifi-enabled dtb below - in that case, it will be spidev0.0 again). | ||
| - | === Sovol mods === | + | ==== Sovol mods ==== |
| Modifications from Sovol useful for this image:\\ | Modifications from Sovol useful for this image:\\ | ||
| Line 147: | Line 152: | ||
| - | === Internal wifi + spidev === | + | ==== Internal wifi + spidev ==== |
| - | + | ||
| - | This is experimental and may not work for you. | + | |
| Replacing the dtb from the '' | Replacing the dtb from the '' | ||
| Line 178: | Line 181: | ||
| * I had some wifi-performance issues with 6.7.5, not sure if that was just by chance. | * I had some wifi-performance issues with 6.7.5, not sure if that was just by chance. | ||
| * The wlan0 device did not show up when " | * The wlan0 device did not show up when " | ||
| + | * To edit the dtb file on your own, use | ||
| + | * '' | ||
| + | * '' | ||
| * The dtb files reside in the fat32 partition, you can easily replace them directly after writing the USB-stick or eMMC. So on the first boot you will automatically be asked to configure wifi. If you set it up using an USB-keyboard instead of a serial line, keep in mind that it uses US-keylayout when entering the passwords. | * The dtb files reside in the fat32 partition, you can easily replace them directly after writing the USB-stick or eMMC. So on the first boot you will automatically be asked to configure wifi. If you set it up using an USB-keyboard instead of a serial line, keep in mind that it uses US-keylayout when entering the passwords. | ||
| Line 185: | Line 191: | ||
| - | === crowsnest / camera streaming === | + | ==== crowsnest / camera streaming |
| * The camera device will probably change after the update. Use '' | * The camera device will probably change after the update. Use '' | ||
| * crowsnest may have problems initializing the camera after reboot. Workarounds: | * crowsnest may have problems initializing the camera after reboot. Workarounds: | ||
| * Manually restart crowsnest service (works reliably, but sucks) | * Manually restart crowsnest service (works reliably, but sucks) | ||
| * Add a pause to crowsnest initialization, | * Add a pause to crowsnest initialization, | ||
| - | * I had to set the pause to 10 seconds, to have it start up reliably | + | * Adding a pause made the startup more reliably, but still not always (tested 5 and 10 seconds) |
| * '' | * '' | ||
| - | * Make sure there aren't any backup copies of '' | + | * Make sure there aren't any backup copies of '' |
| ---- | ---- | ||
| Back to [[start]] | Back to [[start]] | ||
| + | |||
rebuilding.1724748918.txt.gz · Last modified: 2024/08/27 10:55 by torte